Whirlpool WTW7500GW Installationshandbuch PDF herunterladen (Seite 3)

You will need:

A water heater set to 120° F (49° C).

A grounded electrical outlet located within 4 ft (1.2 m) of

power cord on back of washer.

Hot and cold water faucets located within 3 ft (0.9 m) of hot

and cold water ll valves on washer, and water pressure

of 20-100 psi (138-690 kPa).

A level oor with maximum slope of 1" (25 mm) under entire

washer. Installing on carpet is not recommended.

Floor must support washer’s total weight (with water and load)

of 315 lbs (143 kgs).

IMPORTANT: Do not install, store, or operate washer where it will

be exposed to weather or in temperatures below 32° F (0° C).

Water remaining in washer after use may cause damage in low

temperatures. See “Washer Care” in your Use and Care Guide

for winterizing information.

Proper installation is your responsibility.

Recessed area or closet installation

Dimensions show recommended spacing allowed, except for

closet door ventilation openings which are minimum required.

This washer has been tested for installation with spacing of

0" (0 mm) clearance on the sides. Consider allowing more space

for ease of installation and servicing, and spacing for companion

appliances and clearances for walls, doors, and oor moldings.

Add spacing of 1" (25 mm) on all sides of washer to reduce

noise transfer. If a closet door or louvered door is installed,

top and bottom air openings in door are required.

(76 mm)

24 in.

(155 cm

)

48 in.

(310 cm

)

19"

(482 mm)

(25 mm)

(101 mm)

14" max.

(356 mm)

DRAIN SYSTEM

Drain system can be installed using a oor drain, wall standpipe,

oor standpipe, or laundry tub. Select method you need.

Minimum diameter for a standpipe drain: 2" (51 mm). Minimum

carry-away capacity: 17 gal. (64 L) per minute. Top of standpipe

must be at least 39" (990 mm) high; install no higher than

96" (2.44 m) from bottom of washer. If you must install higher

than 96" (2.44 m), you will need a sump pump system.

Wall standpipe drain system

Laundry tub drain system

Minimum capacity: 20 gal. (76 L). Top of laundry tub must be at

least 39" (990 mm) above oor; install no higher than 96" (2.44 m)

from bottom of washer.

IMPORTANT: To avoid siphoning, no more than 4.5" (114 mm)

of drain hose should be inside standpipe or below the top of

wash tub. Secure drain hose with cable tie.

Floor drain system

Floor drain system requires a Siphon Break Kit (Part Number

285834), 2 Connector Kits (Part Number 285835), and an

Extension Drain Hose (Part Number 285863) that may be

purchased separately. To order, please see toll-free phone

numbers in your Use and Care Guide. Minimum siphon break:

28" (710 mm) from bottom of washer. (Additional hoses may

be needed.)

Floor standpipe drain system

4.5"

(114 mm)

39"

(990 mm)

4.5"

(114 mm)

39"

(990 mm)

4.5"

(114 mm)

See requirements for oor standpipe drain system.

1 2 3 4 5 6 7 8 ... 15 16

Kommentare zu diesen Handbüchern

Keine Kommentare

Whirlpool WTW7500GW Installationshandbuch Seite 3

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Waschmaschinen Whirlpool WTW7500GW