Whirlpool KDDD 6010 Installationshandbuch

KDDS 6010 - KDDD 6010Assembly instructions5019_102_00273_INSTAL_GB 30-05-2007 13:25 Pagina 1

OPTION 1and Standpipe Ø38mm with Air Gap.OPTION 2with Waste Disposal. StandpipeØ38mm with Air Gap.PLEASE NOTE: It is NOT recommended toconnect the to

WATER CONNECTIONRecommended COLD (Maximum 60°C).3/4 “ BSP (GB20) to suit flat washer.WATER SOFTENER MODELSRefer to your User Guide on vhow to set up

These marks indicate mounting tab screw locations (refer to step 1 page 7)NOTE: All depth measurements are taken from the front face of the adjacent c

OPTION 1and Standpipe Ø38mm with Air Gap.OPTION 2with Waste Disposal. StandpipeØ38mm with Air Gap.PLEASE NOTE: It is NOT recommended toconnect the to

PLEASE NOTE: Your model of may differ from the model shown in the installation diagrams.Installation is similar for all models either Single or Doubl

Important! (SINGLE MODELS ONLY)The product may move. Mark chassis position on cavity.4 SINGLE MODELS ONLY. Gently open the drawer and mark thechassis

169 - DOUBLE MODELS ONLYAdjust the height of the product to suit the cabinetry, by turningthe feet from inside the product using a wrench or M5 socket

10 SINGLE MODELS ONLYCheck the position of the chassis is still where marked on thecavity, before securing the product.11 There are four 16mm round ho

with Hose Joiner (see Plumbing Options).Remember to slip the wire clip(s) on the drain hose(s) first.15a Slip a wire clip over each drain hose, then p

WARNING!DO NOT plug the product in at this stage.Important!DO NOT cut the inlet hose.17 Connect the Inlet Hose to the water supply. Ensure the sealing

5019_102_00273_INSTAL_GB 30-05-2007 13:25 Pagina 2

Important!Before cutting ensure the Toe Kick is positioned on awooden chopping board to avoid damage to surroundingarea.20 On the chosen groove cut do

• Ensure product is level, securely fastened to the cabinetry and opens and closes freely. The must be free to close with no resistance from the cabin

5019_102_00273_INSTAL_GB 30-05-2007 13:25 Pagina 22

5019_102_00273_INSTAL_GB 30-05-2007 13:25 Pagina 23

5019 102 00273Printed in Italyn05/07GB5019_102_00273_INSTAL_GB 30-05-2007 13:25 Pagina 24

Note to the installer 4Note to the customer 4Parts supplied - double & single models 5Tools needed 5Installation preparation - double & signle

1. Read these instructions completely and carefully. 2. Installation of this requires basic mechanical and electrical skills. 3. Be sure to lea

Parts supplied - double & single modelsDOUBLE MODELSINSTALLATION KITDrain Hose Support (1)Drain Hose Joiner (1)WireClips (2)InstallationTabs (2)Ph

ELECTRICAL PREPARATIONA) The switched power outlet for the appliance should be installed in a cabinet or on a wall adjacent to theunder bench space in

POWER SUPPLY CORDA) Care should be taken when the appliance is installed or removed, to reduce the likelihood of damage tothe power supply cord.B) If

WATER CONNECTIONRecommended COLD (Maximum 60°C).3/4 “ BSP (GB20) to suit flat washer.WATER SOFTENER MODELSRefer to your User Guide on how to set up y

NOTE: All depth measurements are taken from the front face of the adjacent cabinetry.These marks indicate mounting tab screw locations (refer to step