Whirlpool KN1M11S(W)/BA Bedienungsanleitung PDF herunterladen (Seite 5)

Connecting a flexible jointless stainless steel pipe

to a threaded attachment

Make sure that the hose and gaskets comply with

current national legislation.

To begin using the hose, remove the hose holder on

the appliance (the gas supply inlet on the appliance is

a cylindrical threaded 1/2 gas male attachment).

! Perform the connection in such a way that the hose

length does not exceed a maximum of 2 metres,

making sure that the hose is not compressed and does

not come into contact with moving parts.

Checking the connection for leaks

When the installation process is complete, check the

hose fittings for leaks using a soapy solution. Never

use a flame.

Adapting to different types of gas

It is possible to adapt the appliance to a type of gas

other than the default type (this is indicated on the

rating label on the cover).

Adapting the hob

Replacing the nozzles for the hob burners:

1. Remove the hob grids and slide the burners off their

seats.

2. Unscrew the nozzles using

a 7 mm socket spanner (see

 gure), and replace them with

nozzles suited to the new type

of gas (see Burner and nozzle

speci cations table).

3. Replace all the components

by following the above instructions in reverse.

Adjusting the hob burners’ minimum setting:

1. Turn the tap to the minimum position.

2. Remove the knob and adjust the regulatory screw,

which is positioned inside or next to the tap pin, until

the flame is small but steady.

! If the appliance is connected to a liquid gas supply,

the regulatory screw must be fastened as tightly as

possible.

3. While the burner is alight, quickly change the

position of the knob from minimum to maximum and

vice versa several times, checking that the flame is not

extinguished.

! The hob burners do not require primary air

adjustment.

! After adjusting the appliance so it may be used with

a different type of gas, replace the old rating label with

a new one that corresponds to the new type of gas

(these labels are available from Authorised Technical

Assistance Centres).

! Should the gas pressure used be different (or vary

slightly) from the recommended pressure, a suitable

pressure regulator must be fitted to the inlet hose in

accordance with current national regulations relating to

“regulators for channelled gas”.

! If one or more of these conditions is not fulfilled

or if the cooker must be installed according to the

conditions listed for class 2 - subclass 1 appliances

(installed between two cupboards), the flexible steel

hose must be used instead (see below).

TECHNICAL DATA

Oven dimensions

(HxWxD)

34x38x39 cm

Volume

50 l

Useful

measurements

relating to the

oven

compartment

width 42 cm

depth 44 cm

height 23 cm

Power supply

voltage and

frequency

see data plate

Burners

may be adapted for use with any

type of gas shown on the data

plate, which is located inside the

flap or, after the oven compartment

has been opened, on the left-hand

wall inside the oven.

Electric Plate

Standard Ø 145 mm: 1500 W

ENERGY LABEL

Directive 2002/40/EC on the label

of electric ovens. Standard EN

50304

Declared energy consumption for

Natural convection Class – heating

mode:



Static

EC Directives: 2006/95/EC dated

12/12/06 (Low Voltage) and

subsequent amendments -

2004/108/EC dated 15/12/04

(Electromagnetic Compatibility) and

subsequent amendments -

2009/142/EC dated 30/11/09 (Gas)

and subsequent amendments -

2002/96/EC.

1275/2008 Stand-by/ Off mode

1 2 3 4 5 6 7 8 9 10 ... 55 56

Kommentare zu diesen Handbüchern

Keine Kommentare

Whirlpool KN1M11S(W)/BA Bedienungsanleitung Seite 5

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Kochfelder Whirlpool KN1M11S(W)/BA