Whirlpool AKT 760/NE Bedienungsanleitung PDF herunterladen (Seite 2)

After unpacking the hob, check that it has not been damaged during transport. In case of problems, contact the dealer or the

After-sales Service.

PREPARING THE CABINET FOR FITTING

• This product can be fitted in a 20 to 40 mm thick worktop.

• Before installation, make sure:

- the local gas supply conditions (type and pressure) and the hob settings are compatible (see the dataplate

and injector table);

- the side coverings of the cabinet or appliances next to the hob are heat resistant according to the local regulations;

- the appliance is not connected to a fume exhaust device. Installation must be carried out in compliance with the current

regulations. Pay particular attention to the requirements regarding ventilation;

- fumes are exhausted through special extractor hoods or wall and/or window-mounted electric fans.

GAS CONNECTION

ELECTRICAL CONNECTION

IMPORTANT: The details regarding voltage and input are given on the dataplate.

ASSEMBLY

CONVERSION TO DIFFERENT TYPES OF GAS

If a different gas from that specified on the dataplate and the label on the top of the hob is used, the injectors must be

replaced.

Remove the label and keep it with the instruction handbook

Use pressure regulators suitable for the gas pressure indicated in the instructions.

• To replace the injectors, contact the After Sales Service or a qualified technician.

• Injectors not supplied must be requested from the After Sales Service.

• Adjust the minimum of the gas taps.

NOTE: With liquefied petroleum gas (G30/G31), the minimum adjustment (bypass) screw must be tightened down.

IMPORTANT: In case of gradual difficulty in turning the burner knobs, call the authorised After Sales Service Centre

which will replace the cock.

INSTALLATION

WARNING

- Install a separator panel

under the hob.

-The lower part of the

product must not be

accessible after

installation.

- Do not fit the separator

panel if an undertop oven

is installed.

• The distance between the underside of the appliance and the separator panel must respect the dimensions given in

the figure.

• For correct operation of the product, do not obstruct the minimum opening between the worktop and the top of the

cabinet (min.5 mm).

• Carry out all cabinet cutting work before fitting the hob, and carefully remove any shavings or sawdust.

• If an undertop oven is installed, make sure the oven is equipped with a cooling system.

• Do not install the hob above a dishwasher or washing-machine, so that the electronic circuits do not come into

contact with steam or moisture which could damage them.

WARNING

This operation must be carried out by a qualified technician.

• The gas supply system must comply with the local regulations.

• For specific local regulations for some countries, see the section “References to

national regulations”. If no information concerning the required country is given,

ask your installer for further details.

• The connection of the hob to the gas supply or gas cylinder must be by means of a

rigid copper or steel pipe with fittings complying with the local regulations, or by

means of a continuous-surface flexible stainless steel pipe complying with the local

regulations. The maximum permissible length of the flexible metal pipe is 2 metres.

• Carry out the connection using a metal union elbow, interposing a seal to Standard EN

549. The union elbow must be of the type shown in fig. A (ISO 7/1) for all destinations

except France, for which the union must be of the type shown in fig. B (ISO 228/1).

IMPORTANT: If a flexible stainless steel pipe is used, it must be installed in such a

way that it cannot come into contact with any movable part of the furniture, but

runs in an area free of hindrances and can be inspected along all its length.

• After connecting to the gas supply, check for any leaks with soapy water. With the

burners lit, turn the knobs from max. to min. to check flame stability.

Fig. A

Fig. B

min. 5 mm

min. 20 mm

min. 5 mm

WARNING

This operation must be carried out by a qualified technician.

WARNING

• The electrical connections must comply

with the local regulations.

• Earthing of the appliance is compulsory by

law.

• Do not use extension cords.

After cleaning the perimeter surface, fit the

supplied gasket on the hob as shown in the

figure.

Position the hob in the opening made according to the dimensions given in the instructions.

NOTE: The power cable must be long enough to allow removal from above.

To secure the hob, use the brackets (A) provided. Fit the brackets at the holes on the bottom of the hob and fix them with

the appropriate screws so as to adapt them to the thickness of the top (see following figures).

WARNING

This operation must be carried out by a qualified technician.

Earth

(yellow/green)

Top 20 mm Top 40 mm

Top 30 mm

1 2 3 4 5

Kommentare zu diesen Handbüchern

Keine Kommentare

Whirlpool AKT 760/NE Bedienungsanleitung Seite 2

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Kochfelder Whirlpool AKT 760/NE