Whirlpool AKL 710/WH Bedienungsanleitung PDF herunterladen (Seite 3)

After having cleaned the perimeter surface, apply the supplied gasket to the hob as shown in the gure.

PositionthehobintheworktopopeningmaderespectingthedimensionsindicatedintheInstruction.

NOTE: the power supply cable must be long enough to permit its upward extraction.

To secure the hob, use the brackets (A) provided with it. Fit the brackets into the relevant bores shown by the arrow and fasten them by means of their screws in accordance

withthethicknessoftheworktop(seethefollowinggures).

Top 20 mm

Top 30-60 mm

ADJUSTMENT TO DIFFERENT TYPES OF GAS

This operation must be performed by a qualied technician.

If the appliance is intended to operate with a different gas from the gas type stated on the rating plate and information label on the top of the hob, change the injectors.

Remove the information label and keep it with the instructions booklet.

Use pressure regulators suitable for the gas pressure indicated in the Instruction.

• ThegasnozzlesmustbechangedbyAfterSalesServiceoraqualiedtechnician.

• NozzlesnotsuppliedwiththeappliancemustbeorderedfromAfterSalesService.

• Adjust the minimum setting of the taps.

NOTE: when liquid petroleum gas is used (G30/G31), the minimum gas setting screw must be tightened as far as it will go.

IMPORTANT: should you experience difculty in turning the burners knobs, please contact the After Sales Service for the replacement of the burner tap

if found to be faulty.

REPLACING THE INJECTORS (see the injector table in the Instruction)

• Remove grids (A).

• Extractburners(B).

• Using a socket spanner of the appropriate size unscrew the injector (C), unscrew the injector to

be replaced.

• Replace it with the injector suitable for the new type of gas.

• Re-assemble the injector in (D).

• If you have a multiple crown burner use side spanner to replace the injector (E).

Beforeinstallingthehob,remembertoafxthegascalibrationplatesuppliedwiththeinjectorsin

suchawaythatitcoverstheexistinginformationrelatingtogascalibration.

ADJUSTING MINIMUM GAS SETTING OF TAPS

To ensure that the minimum setting is correctly adjusted, remove the knob and proceed as follows:

• tightenscrewtoreducetheameheight(-);

• loosenscrewtoincreasetheameheight(+)

Theadjustmentmustbeperformedwiththetapinminimumgassettingposition(smallame) .

• The primary air of the burners does not need to be adjusted.

• Atthisstage,lightuptheburnersandturntheknobsfrommaxposition to minimum position tocheckamestability.

Uponcompletionofadjustment,resealusingsealingwaxoranequivalentmaterial.

REFERENCE TO LOCAL REGULATIONS

Regulation for room ventilation

Note: Iftheapplianceisnotequippedwithsafetydevicesontheburners(thermocouples),theairventsmustbeincreasedby100%,andmustbeatleast200cm2),

incompliancewithM.D.21April1993.

Connection to gas supply

Before connecting the appliance, make sure that the gas supply system complies with standards UNI-CIG 7129 and UNI CIG 7131.

Gas connection

Theconnectiontothemainsgasnetworkorgascylindermustbemadeusingarigidcopperorsteelpipewithttingscomplyingwithstandards UNI-CIG 7129, or using

a continuous-surface stainless steel hose complying with standards UNI-CIG 9891. Themaximumlengthofthehoseis2m.Thepressurecontrolvalvestobeused

must comply with the UNI EN 12864 standard for gas cylinders and the UNI EN 88 standard for piped methane gas.

AFTER-SALES SERVICE

WARNING