GB15
After unpacking the hob, check that there has been no damage during transport. If in doubt, contact the dealer or After-sales Service.
PREPARING THE HOUSING UNIT
Connecting to the terminal board
For electrical connection, use an H05RR-F cable as specified in the table below.
Connect the yellow/green earth wire to the terminal with the symbol .
This wire must be longer than the other wires.
1. Remove the terminal block cover (A), undoing the screw and inserting the cover in the terminal block hinge (B).
2. Insert the power supply cable into the cable clamp and connect the wires to the terminal board as indicated in the diagram next to the terminal board itself.
3. Secure the power cable with the cable clamp.
4. Close the cover (C) and screw it on the terminal block with the removed screw - point (1).
Each time the cooktop is connected to the mains it carries out an automatic check which lasts several seconds.
If the hob already has a power cable, follow the instructions given on the label attached to the cable. Connect the appliance to the electricity supply by means of an all-pole
disconnect switch with minimum contact gap of 3 mm.
INSTALLATION
WARNING
- Install a separator panel under the
hob.
- The lower part of the product must
not be accessible after installation.
- If there is an oven beneath the hob,
do not install the separator panel.
• For the distance between the underside of the appliance and the separator panel below, observe the dimensions given in the figure.
• In order to ensure the correct operation of the product, do not obstruct the minimum required clearance between the hob and the top of the unit (min. 5 mm).
• Cut the worktop to fit before installing the hob and carefully remove any shavings or sawdust.
• If an oven is installed beneath the hob, make sure that it is equipped with a cooling system.
• For installation in worktops made using marble or other similar materials, do not use the screws supplied; contact the After-Sales Service to request gluing
kit 4812 310 19277. After gluing the brackets in position as indicated on page 3, let the silicone dry for approximately 24 hours before installing the appliance.
• In the case of flush installation, contact the After-Sales Service to request the application of screw kit 4801 211 00112.
• Do not install the hob above a dishwasher or washing machine, to prevent the electronic circuits from coming into contact with steam or moisture and being damaged
as a result.
ELECTRICAL CONNECTION
WARNING
- Disconnect the appliance from the mains power supply.
- The appliance must be installed by a qualified technician who is fully aware of current safety and
installation regulations.
- The manufacturer declines all liability for injury to persons or animals and for damage to property resulting from failure to observe the regulations
provided in this chapter.
- The power supply cable must be long enough to allow the hob to be removed from the worktop.
- Make sure the voltage specified on the appliance rating plate is the same as that of the domestic power supply voltage.
- Do not use extension cables.
Conductors Amount x size
230 V ~ +
3 x 4 mm
2
230-240 V ~ +
3 X 4 mm
2
(Australia only)
230 V 3 ~ +
4 X 1.5 mm
2
400 V 3N ~ +
5 X 1.5 mm
2
400 V 2N ~
4 X 1.5 mm
2
min 5 mm
min 20 mm
min 5 mm
400 V 3N ~ 230 V ~
230-240 V ~ (Australia only)
230 V ~ (UK only)
400 V 2N ~ 230 V 3 ~ (Belgium only) 400 V 2N ~ (NL only)
230 V
230 V
230 V
230 V
230 V
230 V
230 V
230 V
230 V
230 V
230 V
CBA
31902074.book Page 15 Thursday, December 9, 2010 10:42 AM
(4 Seiten)
(15 Seiten)
(20 Seiten)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern