Whirlpool Thin Twin Bedienungsanleitung PDF herunterladen (Seite 3)

Exhaust requirements

^WARNING

Fire Hazard

• Do Not use non-metal, flexible duct.

• Do Not use metal duct smaller than

4 Inches (10.2 cm) In diameter.

• Do Not use exhaust hoods with

magnetic latches.

• Check that exhaust system Is not longer

than specified. Exhaust systems longer

than specified will:

— Accumulate lint.

— Shorten the life of the product.

— Reduce performance and result In

longer drying times and Increased

energy usage.

Failure to follow specifications may result In

a fire.

• Do Not exhaust the dryer Into a

chimney, furnace cold air duct, attic or

crawl space, or any other duct used for

venting.

• Clean the exhaust system every year.

Accumulated lint could be fuel for a fire or

cause moisture damage.

• Exhausting your dryer Indoors Is Not

recommended. The moisture and lint

Indoors may cause:

— Lint to gather Inside and around the

dryer and be a fuel for fire.

— Moisture damage to woodwork,

furniture, paint, wallpaper, carpet, etc.

— Housecleaning problems and possible

health problems.

Failure to follow these Instructions could

result In fire damage, personal Injury or

health problems.

If using an existing exhaust system, clean lint

from entire length of exhaust system. Make

sure exhaust hood Is not plug^d with lint.

The exhaust system should be Inspected and

cleaned yearly.

Replace any vinyl or metallized plastic foil

exhaust duct with rigid metal or flexible

metal duct.

Use duct tape to seal all

joints. Do Not use screws

to secure duct.

exhaust air flow

better

good

Four-Inch (10.2 cm) rigid

metal pipe is preferred.

Plan installation to use

the fewest number of

eibows and turns.

Metal flexible duct must be fully extended

and supported when the dryer is in its final

position. DO NOT KINK OR CRUSH THE DUCT.

The metal flexible duct must be fully

extended to allow adequate exhaust air to

flow.

Allow as much room as possible when using

elbows or making turns. Bend duct gradually

to avoid kinking. Remove excess flexible

duct to avoid sagging and kinking that may

result in reduced air flow.

The exhaust duct can

be routed up, down,

left, right or straight out

the back of the

washer/dryer. Space

requirements are

provided on Panel E

and on the rear panel

of the washer/dryer. Use

the straightest path

possible to avoid 90° '

turns.

Maximum length of the exhaust system

depends upon the type of duct used,

number of elbows and the type of exhaust

hood. The maximum length for both rigid

and flexible duct is shown in the chart.

Mobile home installation

Number

ot90°

turns

43 ft (13.1 m)

33tt(10m)

23 ft (7.0 m)

18 ft (5.5 m)

30 ft (9.1 m)

24 ft (7.3 m)

16 ft (4.9 m)

10 It (3.0 m)

(10.2 cm)

41ft(12.5m)

31 ft (9.4 m)

21 ft (6.4 m)

18 ft (5.5 m)

29 ft (8.8 m)

23 ft (7.0 m)

15ft(4.6m)

9 ft (2.1 m)

2-V2"

(6.4 cm)

36 ft (11.0m)

26 ft (7.9 m)

16 ft (4.9 m)

Not

recommended

24 ft (7.3 m)

18 ft (5.5 m)

10 ft (3.0 m)

Not

recommended

Maximum

length

of 4"

(10.2 cm)

diameter

rigid

metal

duct

flexible

metal

duct

The maximum length using a 2" x 6" rectangular

duct with 2 elbows and a 2-1/2" (TYPE C) exhaust

hood is 8 ft (2.4 m).

For exhaust configurations other than those

listed in chart the back pressure MUST not

exceed 0.2 inches water column at the back

of the washer/dryer. The back pressure should

be checked by a qualified technician.

For exhaust systems not covered by the

exhaust length chart, check with your dealer

or distributor for information.

Service check: The back pressure in any

exhaust system used must not exceed

0.2 inches of water column measured with an

inclined manometer at the point that the

exhaust duct connects to the dryer.

Exhausting the dryer outside is recommended.

Recessed installation that is not exhausted

outside must use Exhaust Deflector Kit Part

No. 694609, available from your authorized

parts distributor. See "Recessed and closet

installation instructions," Panel E, for

unobstructed air opening requirements.

If the washer/dryer Is Installed In a confined

area such as a bedroom, bathroom or closet.

It must be exhausted to the outside and

provision must be made for enough air for

ventilation. Check governing codes and

ordinances. Also refer to the "Recessed and

closet installation instructions" on Panel E.

An exhaust hood should cap the exhaust duct

to prevent exhausted air

___

from returning into dryer. —

The outlet of the hood —

must be at least —

12 inches (30.5 cm) from —

the ground or any object

that may be in the path "

of the exhaust.

Four-Inch (10.2-cm) outlet hood Is preferred.

However, a 2-1 /2 inch (6.4 cm) outlet hood

may be used with short systems only.

A 2-1/2 inch (6.4 cm) outlet hood can result in

ionger drying times than other hood types. For

permanent Installation, a stationary exhaust

system Is required.

Exhausting the dryer through the side of the

washer/dryer requires the use of Side Exhaust

Kit, Part No. 279823,

available from your

authorized parts distributor.

Follow kit Installation

Instructions for proper

exhaust installation.

This appliance Is suitable for mobile home

Installations.

Mobile home exhaust requirements: The

washer/dryer must have an outside exhaust.

If the dryer is exhausted through the floor

and the area under the mobile home is

enclosed, the exhaust system must terminate

outside the enclosed area. Extension

beyond the enclosure will prevent lint and

moisture buildup under the mobile home.

Now start...

With washer/dryer In laundry area.

^WARNING

Personal Injury Hazard

More than one person Is required to lift, tilt

or move the washer/dryer because of Its

weight and size.

Failure to follow this Instruction may result

In personal Injury.

Truck only from the rear to prevent produce

damage.

I Put on safety glasses and gloves.

(30.5 cm)

minimum

Remove cardboard shipping base.

rear legs

4 legs

1 drain hose clamp

1 plastic beaded

strap

4 large, water-

hose washers

• 2 small water-hose

washers

• 1 small clamp

• 2 faucet adapters

• drain hose adapter

and clamp

(not shown)

Remove parts from plastic package.

Check that all parts were included.

Panel B

1 2 3 4 5 6 7

Kommentare zu diesen Handbüchern

Keine Kommentare

Whirlpool Thin Twin Bedienungsanleitung Seite 3

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Waschmaschinen Whirlpool Thin Twin