Whirlpool AKT 759/IX Bedienungsanleitung PDF herunterladen (Seite 4)

ADJUSTING MINIMUM GAS SETTING OF TAPS

To ensure that the minimum setting is correctly adjusted,

remove the knob and proceed as follows:

• tighten the screw to reduce the height of the flame (-)

• loosen the screw to increase the height of the flame (+)

The adjustment must be performed with the tap in minimum

gas setting position (small flame) .

• The primary air of the burners does not need to be

adjusted.

• At this stage, light up the burners and turn the knobs

from max position to minimum position to

check flame stability.

Upon completion of adjustment, reseal using sealing wax or

an equivalent material.

CARE AND MAINTENANCE

To maintain your hob in perfect conditions, clean it after every

use, removing any food spills.

Before any cleaning operation, disconnect the hob from the mains and wait for it to cool down.

CLEANING THE HOB SURFACE

• All the enamelled and glass parts should be cleaned with warm water and neutral detergent.

• The stainless steel surface may become stained in the event of prolonged contact with hard water or aggressive

detergents. Any food spills (water, sauce, coffee, etc.) should be wiped away before they dry.

Clean with warm water and neutral detergent, and then dry with a soft cloth or chamois. Remove baked-on dirt with

specific cleaners for stainless steel surfaces. Remove baked-on dirt from the glass ceramic surface using the scraper tool

(if supplied) and proprietary detergents. Food spills should be cleaned off before they bake onto the glass-ceramic

surface.

• Do not use abrasive or corrosive products, chlorine-based cleaners or pan scourers.

• Do not use steam cleaners.

• Do not use flammable products.

• Do not leave acid or alkaline substances, such as vinegar, mustard, salt or lemon juice on the hob.

CLEANING THE HOB PARTS

• Grids, burner caps and burners can be removed to be cleaned.

• Clean them by hand using warm water and mild detergent, carefully removing any food residues and checking that none

of the burner openings is clogged.

• Rinse and dry carefully.

• Refit burners and burner caps correctly in the respective housings.

• When replacing the grids, make sure that the panstand area is aligned with the burner and that the burners are fitted

properly into their respective housings.

• The end section of electric ignition plugs and safety thermocouples must also be cleaned thoroughly in order to ensure

correct operation. Check these items frequently, and if necessary, clean them with a damp cloth. Any baked-on food

should be removed with a toothpick or needle.

Note: to avoid damaging the electric ignition device, do not use it when the burners are not in their housing.

TROUBLESHOOTING GUIDE

The hob may not work or work incorrectly. Before calling the After-Sales Service, refer to the Troubleshooting Guide to

determine the problem.

The burner fails to ignite or the flame is uneven

Check that:

• The gas or electrical supplies are not shut off and especially that the gas supply tap is open.

• The gas cylinder (liquid gas) is not empty.

• The burner openings are not clogged.

• The plug end is not dirty.

• All the burner parts have been positioned correctly.

• There are no draughts near the hob.

The burner does not stay lit

Check that:

• When lighting the burner, the knob has been pressed for enough time to activate the protection device.

• The burner openings are not clogged near the thermocouple.

• The end of the thermocouple is not dirty.

• The minimum gas setting is correct (see relevant paragraph).

The electric hotplate does not work

Check that:

• The mains electrical supply is present.

• The knob is not turned to

“0”.

The electric hotplate does not switch off

Check that:

• The knob is turned to

“0”.

If this is the case, disconnect the hob from the mains immediately by unplugging it.

Pots/ pans wobble or are unsteady

Check that:

• The bottom of the pot or pan is perfectly flat

• The pot or pan is centered on the burner.

• The grids have not been swapped over or positioned incorrectly.

If after the above checks the fault still occurs, get in touch with the nearest After Sales Service.

AFTER-SALES SERVICE

Before calling the After-Sales Service, make sure you can give the following information:

- type of fault or problem;

- exact model (written on the Product Description Sheet and Warranty);

- service number that follows the word SERVICE on the rating plate under the hob and on the Warranty;

- your complete address and phone number.

If any repairs are required, please contact

an authorised After-Sales Service,

as indicated in the warranty.

Note: Failure to comply with these instructions may compromise the safety and quality of the product.

Manufacturer:

Whirlpool Europe S.r.l.

Viale G. Borghi, 27

21025 Comerio (VA)

ITALY

1 2 3 4

Kommentare zu diesen Handbüchern

Keine Kommentare

Whirlpool AKT 759/IX Bedienungsanleitung Seite 4

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Kochfelder Whirlpool AKT 759/IX