Whirlpool GTE 260 A++ Bedienungsanleitung PDF herunterladen

INSTRUCTIONS FOR USE

1. Handle

2. Electronic control panel

3. Safety lock (if provided)

4. Separator (if provided)

5. Defrost water drain plug

6. Motor compartment vent

7. Upper edge

8. Seal

9. Ice packs (if provided)

10. Basket (if provided)

1. Digital temperature display: indicates the

temperature inside the freezer (fixed display) or the

set temperature (blinking display).

2. Temperature decrease button: press for a colder

temperature setting.

3. Temperature increase button: press for a warmer

temperature setting.

4. “Big load” button: press to activate/deactivate the

big load freeze function.

5 “Big load” LED (yellow): indicates activation of the

big load freeze function.

6. “Sensor” activation LED (blue): indicates

activation of the “Dynamic Intelligence” function (see

section “Dynamic Intelligence Function”).

7. Alarm reset button: deactivates the acoustic alarm

and the power failure alarm LED (see section

“Alarms”).

8. Alarm LED (red): blinks to indicate an alarm

condition (see section “Alarms”).

INSTALLATION

• Refer to the section “BEFORE USING THE

APPLIANCE”.

• Unpack the appliance.

• Remove the 4 spacers inserted between the

door and the appliance.

• Make sure the defrost water

drain plug (if provided) is

correctly positioned (5).

• For best appliance

operation and to avoid

damage when the door is

opened, leave a space of at

least 7 cm from the rear wall and 7

cm at the sides.

• Fit the accessories (if provided).

SWITCHING ON THE FREEZER

• Plug in the appliance.

• When the appliance is warm (internal

temperature above 0°C), two dashes

appear on the digital display (1).

• The red alarm LED (8) blinks and the acoustic alarm

sounds.

• The “Sensor” LED (6) is on.

• Press the reset button (7) to deactivate the acoustic

alarm.

• The acoustic alarm stops while the red alarm LED

continues to blink.

• When the appliance reaches a temperature of at least

-12°C the red LED (8) stops blinking.

• Food can now be placed in the freezer.

• The “Sensor” LED (6) stays on until the temperature

set on the display is reached.

NOTE: As the seal is tight, the freezer door cannot be

reopened immediately after closing. It is necessary to

wait a few minutes.

Freezer temperature adjustment

The appliance is normally factory-set for operation at

the recommended temperature of -18°C. The internal

temperature setting can be adjusted between -17°C and

-24°C and in ECONOMY mode (see section “ECO

function”), proceeding as follows:

• Press one of the two temperature adjustment buttons

once (2; 3).

• The digital display (I) will blink, showing the previous

temperature setting.

• Press the button (3) as required for a warmer

temperature setting. The value changes by 1°C with

each press of the button. During this operation the

value shown on the digital display blinks.

1 2 3 4 5 6

INSTRUCTIONS FOR USE 1

Inhaltsverzeichnis

Seite 1 - INSTRUCTIONS FOR USE

INSTRUCTIONS FOR USEGB1. Handle2. Electronic control panel3. Safety lock (if provided)4. Separator (if provided)5. Defrost water drain plug6. Motor co

Seite 2

INSTRUCTIONS FOR USE• Press the button (2) as required for a coldertemperature setting. The value changes by 1°C witheach press of the button. During

Seite 3

FREEZING FOODOnly use the freezer for storing frozen food,freezing fresh food and making ice cubes. Preparing fresh food for freezing• Before freezing

Seite 4

INSTRUCTIONS FOR USEPRECAUTIONS AND SUGGESTIONSInstallation• The appliance must be handled and installed by two ormore people.• Be careful not to dama

Seite 5

INSTRUCTIONS FOR USE• To prevent the risk of children becoming trapped andsuffocating, do not allow them to play with theappliance.• Do not swallow th

Seite 6

INSTRUCTIONS FOR USEAFTER-SALES SERVICEBefore contacting the After-Sales Service:1. See if you can solve the problem yourself.2. Switch the appliance