Whirlpool ADG 2020 FD Bedienungsanleitung PDF herunterladen (Seite 2)

EN -2-

First time use

1- salt reservoir

2- rinse aid dispenser

3- detergent dispenser

4- racks system

5,6,7,8- available functions on the panel

9- filters

10- spray arms

11- PowerDry technology

Water hardness should be set before

the first wash or if water hardness

has been changed

Visual indicator

(depending

on the model).

Unscrew cap.

The salt level indicator lamp may remain lit

at the end of several wash cycles. If the

water hardness set to level 1 (soft), no salt

is required and salt indicator lamp will

remain off.

(depending on the model)

Salt indicator on the control panel Salt indicator on the salt reservoir cap

The indicator lamp lights up when SALT

NEEDS TO BE ADDED.

green: OK.

clear: NEEDS TO

BE ADDED

Daily check

Filling the salt reservoir - Dissolve limescale (not necessary if water hardness level is set to “soft 1”!)

Screw on the cap.

Salt residual

around the cap

need to be

removed. Some

salt reservoir have

a level indicator

integrated in the

cap (see below

how to check).

Once regeneration salt is added, immediately start a wash program (the “Pre-wash” program alone is not sufficient). Residual saline solution or grains of salt

can lead to deep-down corrosion, irreparably damaging the stainless steel components. The guarantee is not applicable if faults are caused by such circumstances.

Fill the salt reservoir with water

before the first wash only.

Add salt (never add detergent!)

min. 0.8 kg / max. 1 kg

Water hardness level is

factory set for medium-hard

water (level 4).

Detergents

When you use Powder or

Gel you must use salt and set

up water hardness level as

indicated in the table on the

right.

Also when you use

Tablets which include salt

functionality you must still

add regeneration salt.

1. Ask your water supply company what the water hardness is... 2. ...enter this value on

your dishwasher

SALT

required

German

degrees °dH

French

degrees °fH

English

degrees °eH

Water hardness

level

Insert value is shown

in the display

0 - 5 0 - 9 0 - 6.3 Soft 1 NO

6 - 10 10 - 18 7 - 12.6 Medium 2

YES

11 - 15 19 - 27 13.3 - 18.9 Average 3

16 - 21 28 - 37 19.6 - 25.9 Medium-hard 4

22 - 28 38 - 50 26.6 - 35 Hard 5

29 - 35 51 - 63 35.7 - 44.1 Very hard 6

36 - 50 64 - 90 44.8 - 62.4 Extremely hard 7

How to set water hardness in order to always assure the best cleaning results

- Press and hold together and buttons for minimum 3 seconds.

- The current water hardness setting will be visible on the display.

- Press the button to increase setting. Value range goes from 1 to 7 (when the level reaches 7, the next press of the

start button will set the level back to 1).

- Wait 30 seconds (control panel switches off) or press button to save setting.

Before first use, run the appliance with detergent and without loading.

1 2 3 4 5 6 7 8

Kommentare zu diesen Handbüchern

Keine Kommentare

Whirlpool ADG 2020 FD Bedienungsanleitung Seite 2

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Geschirrspüler Whirlpool ADG 2020 FD